How to reconstitute CJC-1295 Ipamorelin
Step-by-step guidance for combining CJC-1295 and ipamorelin in a vial with bacteriostatic water, plus the units in each dose afterward.
- sizes of the vials sold
- 5, 10, 20, 55 mg
- 2.5 mg/mL from 5 mg with water
- 2 mL
- bac water once opened
- 28 days
Mixing CJC-1295 with ipamorelin: a step-by-step guide
- Wash your hands, then use an alcohol swab to wipe the bacteriostatic water, the peptide vial and both rubber stoppers.
- Pull the chosen water into the syringe. Adding 2 mL to a 5 mg vial gives 2.5 mg per mL.
- Insert the needle at a slight angle through the stopper; let the water run slowly along the vial's inside wall.
- Gently roll the vial in your hands until the powder is gone. Don't shake it.
- Mark the mix date on the vial and keep it as your product or prescription directs.
- First work out your dose in units, then draw the syringe to that mark.
How to mix a 5 mg vial
Adding 2 mL of water to a 5 mg vial produces 2.5 mg per mL. With that mix, 250 mcg comes to 10 units, while 1 mg comes to 40 units. If you use 1 mL instead, each mL contains 5 mg, so the same 250 mcg equals 5 units.
Reconstitution chart for CJC-1295 and ipamorelin
| Vial | Water added | Strength | Units for a sample dose |
|---|---|---|---|
| 5 mg | 1 mL | 5 mg/mL | 5 units for 250 mcg |
| 5 mg | 2 mL | 2.5 mg/mL | 10 units for 250 mcg |
| 5 mg | 3 mL | 1.667 mg/mL | 15 units for 250 mcg |
| 10 mg | 1 mL | 10 mg/mL | 2.5 units for 250 mcg |
| 10 mg | 2 mL | 5 mg/mL | 5 units for 250 mcg |
| 10 mg | 3 mL | 3.333 mg/mL | 7.5 units for 250 mcg |
| 20 mg | 1 mL | 20 mg/mL | 5 units for 1 mg |
| 20 mg | 2 mL | 10 mg/mL | 2.5 units for 250 mcg |
| 20 mg | 3 mL | 6.667 mg/mL | 3.8 units for 250 mcg |
| 55 mg | 2 mL | 27.5 mg/mL | 3.6 units for 1 mg |
| 55 mg | 3 mL | 18.333 mg/mL | 5.5 units for 1 mg |
| 55 mg | 5 mL | 11 mg/mL | 9.1 units for 1 mg |
| 55 mg | 10 mL | 5.5 mg/mL | 4.5 units for 250 mcg |
CJC-1295 and ipamorelin dose units
What the label shows
No use in people is FDA-approved; it is sold as a research chemical. Because there is no FDA label, official mixing instructions do not exist; follow what came with the product.
Questions people ask
How much bacteriostatic water do you need with 5 mg of CJC-1295 and ipamorelin?
No single amount is the right one. With 2 mL, you get 2.5 mg per mL; adding water lowers the strength of each unit, so small doses are easier to draw.
Can I mix CJC-1295 and ipamorelin with sterile water?
Since sterile water has no preservative and is for single use, a mixed vial that you draw from over several days usually uses bacteriostatic water. Compare bacteriostatic and sterile water.